Posted on Leave a comment

Ultrasonic Accessories for Spooky Central Plasma Machine

Ultrasound is generally defined as sound above the upper limit of human hearing, which is 20,000Hz, and it ranges from 20,000Hz all the way up to several thousand MHz. Humans cannot hear it, but many animals, fish, marine mammals and insects can. So just like Spooky Central’s plasma, ultrasonic, it is also a frequency that can be applied directly without any carrier, but what is special about it is that sound conducts much better in water and solids than in air, due to Our body is 70% water and the remaining 30% is mostly solid, which means that ultrasound can flood the entire body with frequencies.

To use the ultrasonic accessory, you should place the metal diaphragm on the bare skin; if the diaphragm is close to but not touching the skin, the ultrasonic will also work, because the sound waves will pass through the air, but the energy will not be transmitted as efficiently to the body , the technology won’t work as well as it should.

Two settings are available for Ultrasonics: “Slow” divides the output frequency of the plasma by 256, and “Fast” divides it by 16; this means that the Fast frequency will be higher than the frequency produced by the Slow, also the “Slow” output The power will be stronger than “Fast”, so you should use Fast first, and then consider using “Slow” after getting used to it.

Due to the limitations of the metal diaphragms used in ultrasound transducers, this application method is not suitable for use with the Frequency sweep program.

Finally, ultrasound requires frequency input from a generator, can be used alone or in combination, and is safe and usable for those with pacemakers and other electronic implants as an alternative to inappropriate TENS pads and PEMFs .

Posted on Leave a comment

Youtube (Spooky2) Frequency Healing for Measles

Measles is a highly contagious respiratory disease that can cause serious complications, including seizures, brain damage and even death. Measles is caused by a viral infection that first infects the respiratory tract, however, it eventually spreads to other parts of your body through the bloodstream. There is no specific treatment for measles, but the condition usually improves within 7 to 10 days. There are several things you can do to help relieve symptoms, such as getting enough rest, drinking enough water, or taking medicine.

Welcome to listen to the following youtube frequency video will help relieve runny nose, tiredness, cough, it is recommended to listen to it at least 2-3 times a day, keep the moderate volume at a comfortable level to prevent any hearing damage, make sure you have enough lemonade or Purified water to flush toxins from your body.

Posted on Leave a comment

Spooky2 Frequency Healing for COVID-19 Coronavirus

At present, the new round of Delta and Omicron epidemics of the new crown pneumonia are spreading in Hong Kong. The situation is getting out of control and seriously affecting people’s lives. In addition to worrying about getting the Covid-19, many people are more worried about being quarantined or being sent to Penny’s Bay. Suspected patients should also go to the test frequently, and may wait in queue for 3 to 4 hours for testing, which is really a disappointed arrangement.

At present, there is no specific medicine that can completely prevent or treat the COVID-19, but only use medicine to relieve symptoms. Many foreign governments recommend that patients stay at home and let the disease recover on their own. It is not advise to go to the hospital for non-serious cases. For the current situation, I will introduce the use of Spooky2 frequency healing. Spooky2 has the following Covid-19 programs available. You can use these programs for remote treatment, which may help patients to speed up recovery or reduce symptoms. If there is anyone in need, you can contact me and mail a few nails to me to try to run this healing remotely. I hope it will help patients.

Posted on

Steps to Make Colloidal Silver with Spooky2

Colloidal silver, usually in liquid form and used in medicine for a long time, attaches to proteins on bacterial cell walls and disrupts their membranes; silver ions can penetrate into cells, where they interfere with bacterial metabolism process, and damage their DNA, eventually the bacteria will die. The following steps are to make nanoparticulate colloidal silver with Spooky2, the silver particle size will be very small to increase the effectiveness of the colloidal silver.

Step 1: Prepare those devices

  • Spooky2 XM Generator or Spooky2 GeneratorX x1 (includes power adapter, USB cable and BNC/Alligator cable)
  • Spooky2 Boost v3.0 x1
  • Silver Rod x2
  • Magnetic stirrer x1
  • glass or ceramic container
  • distilled water

Step 2: Washing

Thoroughly clean the Spooky Silver Rod and Container, rinse with distilled water and dry with a napkin.

Step 3: Hardware Connection

  1. Fill the container with distilled water (do not use tap or filtered water, these will almost certainly contain unwanted impurities and chemicals; it is normal for your silver rod to turn grey, however, if your water has impurities, it will turn black; Hot water will speed up the process, but the particle size will increase.).
  2. Place two clean, shiny silver rods in the water, making sure the rods are at least an inch or more apart.
  3. Place the container on the magnetic stirrer and insert the small plastic stirrer.
  4. Clip the alligator clip to the silver rod and plug the other end of the cable into the Spooky2 Boost’s colloidal silver port.
  5. Cover the container with a lid, such as plastic wrap, to keep dust or dirt out.
  6. Connect the generator to the computer’s USB port and plug in the power adapter.

Step 4: Software Setup

  1. Open the Spooky2 XM (GX) generator and launch the Spooky2 software on your PC.
  2. Click Utilities in the top menu. Select Colloidal/Ionic Silver Calculator and a new window will pop up.
  3. Enter parameters to calculate when you should run the colloidal silver generation program.
  4. Use the “By Calculation” method to calculate the duration of the program, you can change any field in the calculator, enter the volume of distilled water, for example 500 ml; enter PPM, which is the desired parts per million, we recommend this Set to 20PPM, which is the strength of most commercial colloidal silver; enter the current, if you don’t have the tools to measure the current or don’t know how to measure it, just enter 0.2mA. This is a rough average estimate, assuming you have two 9 AWG rods one inch apart immersed in distilled water to a depth of 12 inches, the total time required to make colloidal silver will automatically be displayed next to the duration in minutes , hours, and days are given in units.
  5. Exit the calculator and go to the Presets tab.
  6. Open the Miscellaneous catalog and select Preset Colloidal Silver Generation – JW Preset.
  7. Go to the Programs tab and enter the calculated duration (750 minutes) you received from step 3 into the Dwell Multiplier field.
  8. Go to the Control tab, tick “Override generators”, select a generator and run the program.
  9. Turn on the magnetic stirrer. Adjust the gentle movement of the water, speed is not the key, don’t rush the manufacturing process, the slower the better.

Result: When the colloidal silver solution is ready, it may be pale yellow/gold, which indicates that the particle size is very small, and you can shine a laser in the solution and observe a visible red line indicating tiny silver particles in suspension. Store colloidal silver solutions in dark glass containers, plastic and UV rays from the sun can cause silver ions to lose their positive charge and clump together, impairing their healing abilities.

Posted on Leave a comment

Why is the Spooky2 Biofeedback Scan Result Different Every Time?

A recent Israeli study, “The amount of bacteria carried by the average person,” found that the human body has an average of 30 trillion human cells and 39 to 50 trillion bacterial cells, and it is unbelievable that the vast majority of these bacteria are Harmless, some beneficial and actually vital to life, 70% of our immune system is made up of this “good bacteria”.

All human bacterial cells – good, bad and harmless – operate at frequencies between 76,000Hz and 880,000Hz. When you perform a frequency sweep, you enter the entire range of amplitudes covering frequencies. At the same time as your first scan, many different bacteria are likely to be killed, and the frequency will cause a reaction in your body, and the scan will record their frequency. After that, you treat according to the scan results, you will kill them all, and your next scan will not find them.

Another complicating factor is that due to time, each scan can only look for the top 10 hit frequencies in your body, however some peripheral bacteria seem to die “noisier” than others – we call it These species are the “loudest screamers” because they elicit an extreme response in the body, and since biofeedback scans cannot distinguish between harmful and innocuous, the Spooky Pulse or GX will record all of them. On the other hand, nasty stealth pathogens have evolved ways of evading the immune system so they go unnoticed, and as a result, their frequencies may not be picked up and recorded at first. With each scan, you may find another 10 “loudest screams,” and even these may not include frequencies relevant to your disease.

To do this, you must first remove all the loudest noise makers – peripheral bacteria by repeating the scan, and when this is done, there will be no more “loudest screams” to drown out these dying viruses and bacteria, Your results will now include their true frequencies. There are other factors involved, for example, killing bacteria always releases the virus that infects them as well as toxins, and some bacteria that survive the first scan may turn into “cysts” or other forms that are less likely to kill the next time . Killed parasites release bacteria, viruses, toxins and heavy metals. This means that the frequency of your flashover is in a state of constant change, and it is different from moment to moment. Given all of this, it’s unreasonable to expect repeatability in sequential scans, and it’s unrealistic to believe that one or two scans will solve all your problems, so it’s unrealistic to scan successive layers of pathogens and trace the source, like peeling layer by layer. onion. That’s why our recommended method is to scan, use your follow-up scan results 7-8 times in contact mode, then scan again, and continue this way until you reach your health goals.